Effect of drilling fluid particle sizes on formation damage: application to horizontal well

(2001) Effect of drilling fluid particle sizes on formation damage: application to horizontal well. Masters thesis, King Fahd University of Petroleum and Minerals.

[img]
Preview
PDF
10174.pdf

Download (3MB) | Preview

Arabic Abstract

في هذه الدراسة استخدمت أربع عينات من طين الحفر المائي البليمري المضاف إليه مواد مجسرة تتكون من جسيمات متعددة الأحجام لدراسة تأثير حجم الجسيم وطول مدة الغمر على إتلاف الطبقات . وأجريت التجارب باستخدام جهاز مانع للتسرب كما استخدمت موجات فوق الصوتية في قياس أعماق تسرب مرشحات طين الحفر والجسيمات داخل العينات اللبية . ولقد أظهرت النتائج أنه كلما كبر حجم الجسيمات كما قل عمق تسرب المرشحات وكلما زاد قيمة النفاذية المسترجعة . كما لوحظ أن طول مدة الغمر يتلف النفاذية ويزيد من عمق التسرب مما يؤدي إلى زيادة معامل القشرة . ولوحظ أيضاً في كل التجارب بلوغ أقصى عمق للتسرب بعد مرور أربع ساعات من بداية الغمر ويعزى ذلك لعدم وجود طبقة مرشحة تمنع موانع طين الحفر والجسيمات من التسرب . ولتحقيق أقل تلف أو ضرر للطبقات يتوجب اختيار أحجام مناسبة للجسيمات المضافة ليس فقط لتقليل أعماق التسرب ولكن أيضاً لترشيح الجسيمات الغروية الدقيقة مثل البليمر . كما تستعرض الدراسة مثالاً عن كيفية تطبيق نتائج هذا البحث في حفر الآبار الأفقية .

English Abstract

Four XC-Polymeric water based mud systems with different median particle sizes of the bridging additives were used to study the effect of particle size distribution and flooding time on formation damage. The experiment was conducted using Leak-Off experimental setup. An Ultrasonic technique, a non-destructive method was implemented to measure depth of invasion by the drilling fluid filtrates and particles on a Berea core samples. The results of this experimental work proved that an increase in the median particle size of the bridging additive would decrease the invasion depth and increase the return permeability. It is also observed that as flooding time increases, permeability impairment and invasion depth increased, which resulted in an increase of the skin factor. For all of the drilling fluid types studied, the largest invasion depth was observed in the first four hours flooding time. This is due to the absence of well-established, low permeable filter cake to protect the formation from invasion by drilling fluid filtrates and drilling fluid particulates down to colloidal sizes. In sizing particles in the drilling fluid system, it is important to consider not only the invasion of particles, but also the invasion of particulates down to colloidal sizes like the polymers. It is possible to achieve minimum formation impairment by properly sizing the particles, not only to minimize the invasion depth into the formation, but also to effectively filter out the smaller polymers and other colloidal particulates in the drilling fluid system. An example is presented at the end to show how this experimental work can be applied to horizontal well.

Item Type: Thesis (Masters)
Subjects: Petroleum
Department: College of Petroleum Engineering and Geosciences > Petroleum Engineering
Committee Advisor: Al-Majed, Abdulaziz A.
Committee Members: Khan, Mohammad A. and Al-Gadhib, Ali H. and Menouar, Habib K.
Depositing User: Mr. Admin Admin
Date Deposited: 22 Jun 2008 13:58
Last Modified: 01 Nov 2019 13:57
URI: http://eprints.kfupm.edu.sa/id/eprint/10174