RETROFITTING OF EXTERIOR BEAM-COLUMN JOINTS USING CFRP

RETROFITTING OF EXTERIOR BEAM-COLUMN JOINTS USING CFRP. Masters thesis, King Fahd University of Petroleum and Minerals.

[img]
Preview
PDF
Danish_Ahmed_MS_Thesis..pdf

Download (7MB) | Preview

Arabic Abstract

شعاع العمود المشترك هو عنصر هام من الإطارات الخرسانة المسلحة ويجب أن تصمم هذه المفاصل ومفصلة بشكل صحيح، وخاصة بالنسبة للتحميل دوري، كما هو الحال مثلا عندما يتعرض الإطار لتحميل الزلزال. وقد أدت الوعي مؤخرا الحدث الزلزالي المحتملة في مناطق منخفضة إلى معتدلة الزلزالية للمملكة العربية السعودية مخاوف من سلامة والضعف للمنشآت الخرسانية المسلحة، والتي لم يتم تفصيل الدكتايل المنصوص عليها صراحة في عملية التصميم. وتستند معظم المباني في هذه المناطق مصممة على الحمل الجاذبية والرياح الأحمال والسلوك من شأنه أن يكون غير قابل للسحب في حالة وجود الحدث الزلزالي والتي يمكن أن تؤدي إلى خسائر في الأرواح والاضطراب الاقتصادي الشديد. والهدف من هذه الدراسة هو التحقيق في سلوك الفقراء المفاصل شعاع عمود مفصلة تحت رأسي ودوري حمولة ساكنة. هذه المفاصل هي الحزم العمود ممثل بناء مفصلة الموجودة في منطقة نشطة زلزاليا في المملكة العربية السعودية. تم اختبار ثلاثة أنواع من العينات مع تفاصيل مختلفة وتعزيز، منها اثنان من وجود مع "ρ" الصغيرة واحد مع "ρ" أعلى، نتيجة التجريبية يظهر النوع الثاني من الفشل بين "ρ" الصغيرة وعالية، والعينات مع انخفاض "ρ" فشل بسبب عدم الانحناء والعينات مع "ρ" عالية فشل بسبب فشل المشترك في إطار من القص الذي يتم التحقق من صحة الحسابات من قبل الآلية / تجريبية وأيضا عن طريق استخدام النمذجة DIANA-دراكر براجر مع التوتر وقطع تخفيف التوترز ودرس أيضا CFRP التعديل التحديثي للمفاصل العمود شعاع عبر الاقتداء العينات مع الاتحاد الدولي للاتصالات منخفضة جدا ملموسة في قوة الضغط DIANA وتحليل العناصر المحدودة يبين علاقة جيدة جدا مع النتائج التجريبية لكل من السيطرة والعينات التعديلي

English Abstract

Beam column joint is an important component of reinforced concrete frames and these joints should be designed and detailed properly, especially for cyclic loading, as for example when the frame is subjected to earthquake loading. Recent awareness of a potential seismic event in low to moderate seismicity regions of Saudi Arabia have led to concerns of the safety and vulnerability of reinforced concrete buildings, in which ductile detailing has not been provided explicitly in the design process. Most of the buildings designed in these regions are based on gravity load and wind loads and their behavior would be non-ductile in case of a seismic event and which could lead to loss of human life and severe economic disruption. The objective of this study is to investigate the behavior of poor detailed beam-column joints under vertical cyclic & static load. These beam-column joints are representative of existing detailed building in seismically active area of Saudi Arabia. Three types of specimens were tested with different detailing and reinforcement, out of which two were having with small “ρ” and one with higher “ρ”, experimental result shows two type of failure between small and high “ρ”, the specimens with lower “ρ” fails due to flexural failure and specimens with high “ρ” fails due to failure of joint under shear which is validated by the mechanistic /experimental computations and also by DIANA modeling using Drucker-Prager with tension cut-off and tension softening. CFRP retrofitting of beam column joints were also studied by modeling the ITU specimens with very low compressive strength concrete in DIANA and the Finite Element analysis shows very good correlation with experimental results for both control and retrofitted specimens.

Item Type: Thesis (Masters)
Subjects: Civil Engineering > Structural Engineering
Department: College of Design and Built Environment > Civil and Environmental Engineering
Committee Advisor: Baluch, M.H
Committee Members: Algadhib, A and Al-Gahtani, H.J and Alfarabi, M.S
Depositing User: AHMED DANISH (g200902070)
Date Deposited: 12 Jan 2013 10:52
Last Modified: 01 Nov 2019 15:37
URI: http://eprints.kfupm.edu.sa/id/eprint/138825